Filing a claim is easier with good records. We document everything and talk to your adjuster for you.
The sooner drying starts, the less there is to repair. Our phones are answered around the clock, with same-day visits when available.
Certified technicians, professional drying equipment and moisture readings you can see for yourself. No guesswork.
Most people who call us have never dealt with hardwood floor water damage before. We walk you through it on the phone, then send a local crew with the right equipment.
Hardwood responds fast when it gets wet. Boards take on moisture from below and from the edges, swell against each other and start to cup, with the edges rising higher than the center. A floor in this condition is not necessarily ruined. When drying starts within the first few days, solid hardwood frequently lies flat again. The key is pulling moisture out of the boards and the subfloor underneath at a steady, controlled pace.
Our tool for hardwood is the floor drying mat. The mats are sealed to the surface and connected to a vacuum unit that draws moisture up through the boards and seams, while dehumidifiers keep the room air dry. Compared with carpet or drywall it is slower, commonly a week or more. No sanding should happen before the wood has dried completely. Sand a cupped floor too soon and it will crown later.
We take readings on the boards, the subfloor and unaffected flooring nearby for comparison. The comparison shows how far down moisture reached and how likely the floor is to recover.
Rugs and furnishings come off the affected boards while pooled water is vacuumed up at once. Cutting off the water entering the joints early keeps swelling down.
We tape drying mats to the floor and attach them to a vacuum system, which draws moisture upward through the wood. Dehumidifiers control the room so the wood dries evenly without cracking.
Readings are logged every one to two days and the equipment stays until the wet zone equals the dry comparison areas. Our final advice is one of three outcomes, no further work, swapping a few boards, or refinishing the floor.
High heat or too much airflow pulls moisture from the surface faster than the core can follow. Lasting gaps and split or cracked boards are the usual outcome.
Staples and flooring nails corrode when moisture lingers, and their grip weakens. The rust also bleeds into the wood as dark stains that sanding may not remove.
Between the boards and the subfloor there is only darkness and still air. You will smell it before you see it, because nothing shows on the surface.
Sanding cupped boards flat while they are still wet removes the raised edges. When the wood finishes drying, the centers end up high and the floor is crowned.
We save what can be dried properly and remove only what cannot. Moisture readings make that call, not guesswork.
Ask a Tech: (475) 203-3930| Material | Can usually be saved when | Has to be replaced when |
|---|---|---|
| Plywood subfloor | Wet but flat and firm, dried to a normal reading | Layers separating, soft spots or visible mold growth |
| Solid hardwood | Boards that cupped but remain nailed tight, if dried within days | Boards that buckled, cracked or turned black, plus anything touched by sewage |
| Engineered hardwood | Planks wet only briefly on the surface, edges still tight | Planks that are delaminating, swollen or wet underneath |
| Floor finish | Slight whitening that disappears when the wood dries | Peeling or stained finish, which needs a sand and refinish |
| OSB or particle board | Only OSB showing no edge swell | Swollen OSB and nearly any wet particle board |
Water slips through the seams and spreads between the boards and subfloor. The surface may wipe dry while the underside stays soaked.
Boards swell and the edges rise. A cloudy look can appear in the finish. Mold can begin on the subfloor and the unfinished underside of the wood.
Pressure grows through the whole floor as the wood expands. Edges get crushed together, nails work loose and parts of the floor may start rising from the subfloor.
Buckling, black staining and mold under the boards become likely. Drying is usually no longer enough, and the bulk of the wet flooring has to be replaced.
Not seeing your question? Call and ask. It costs nothing to talk it through.
Call (475) 203-3930Take action now and prevent costly damage. Huntington Beach Restoration is ready to help.
Call (475) 203-3930 Now